Licensed C-57 Well Drilling Contractor · CSLB #1146787C-57 Well Drilling · CSLB #1146787
Big River Drilling
Almond orchard rows on micro sprinklers in the San Joaquin Valley
Call (559) 867-3806 Get a Free Estimate

PVC vs steel well casing: which one belongs in your well?

California’s well standards allow both PVC and steel well casing, and neither one is right for every well. Those standards, DWR Bulletin 74, name steel as the casing used most often, especially in drilled wells. They name PVC as the plastic casing used most often in California.

The choice turns on the well’s depth and diameter, the ground and how corrosive the water is. It also turns on how the casing goes in: steel can be driven into place, and plastic must not be. Cost plays a part too, and the estimate for your well should name the casing.

What does casing do in a water well?

Casing is the pipe that lines a drilled well. Bulletin 74 gives it three jobs. It holds the hole open, carries the water up and helps protect the water’s quality.

The standards say casing must be strong and tough enough to resist the forces on it, during installation and after. Galvanized sheet metal pipe, such as downspout pipe, is not allowed as well casing. Neither is wood.

Casing is one line on every estimate for water well drilling, for a new well or a replacement. That line should name the material, the diameter and how deep the casing runs.

How do PVC and steel well casing compare side by side?

This table draws on the state’s well standards and a home-improvement cost guide. The prices are market numbers, not our price list.

What to comparePVC casingSteel casing
How common it isThe plastic casing used most often in CaliforniaThe casing material used most often, especially in drilled wells
The standard it must meetASTM F480, plus NSF Standard 14 and its marking in drinking water wellsSteel pipe specs listed in Bulletin 74; stainless steel meets ASTM A409
Deep and wide wellsLarge diameter plastic has seen little use below 500 feet, so it needs special careThe cost guide calls steel much stronger for deep wells
CorrosionWill not rust; the cost guide calls it best for acidic waterGalvanized resists corrosion less; stainless adds corrosion protection
JointsSolvent welded or threadedWelded, threaded or joined with threaded couplings
Driving it into placeNever allowedAllowed, with a drive shoe at the lower end
Heat from a cement sealHeat can weaken and collapse it, a special concern with thin wallThe heat warning in the standards is written for plastic
Storage on siteOut of direct sun, kept from bending and hard knocksThe storage rule in the standards is written for plastic
Market price per foot$6 to $10$36 to $140, galvanized or stainless

Which casing holds up better in a deep or wide well?

A home-improvement cost guide calls galvanized steel much stronger for deep wells. Bulletin 74 notes that large diameter plastic casing has not been used extensively below 500 feet. It calls for special care with plastic in deep wells.

Plastic casing that may take significant impacts must meet an impact resistance class in ASTM F480. Casing set in large diameter, deep holes is one example the standards give. For steel, the standards leave the wall thickness to good design practice and the conditions at the well site.

The diameter also decides the pump. A university extension guide says the casing receives the pump, so the pump size must be settled before drilling starts. It says a 6-inch casing takes pumps that move up to 100 gallons per minute. Above 100, it calls for an 8-inch casing in at least a 10-inch hole.

That is why the casing and the well pump installation get planned together. The same guide says an irrigation well usually needs to produce more water. So agricultural and irrigation wells tend to take wider casing.

Does steel well casing rust, and how does PVC handle corrosive water?

Plastic casing will not rust. A home-improvement cost guide calls PVC best for corrosion resistance in more acidic, low-alkaline water.

Steel depends on the type. The same guide says galvanized steel resists corrosion less than other casing types. It says stainless steel offers similar strength with better corrosion protection. Bulletin 74 gives stainless casing its own standard, ASTM A409, written for corrosive or high temperature service.

The seal around the casing can help too. Bulletin 74 says that in some cases, the annular seal also protects casing against corrosion.

How does each casing go into the ground?

Steel casing may be joined by welds, threads or threaded couplings. It may also be driven into place, with a drive shoe at the lower end. Plastic casing joins by solvent welding or threads. Bulletin 74 says it must not be driven or put under excessive stress during installation.

The seal brings its own concern. Cement gives off heat as it sets, and Bulletin 74 warns that heat can weaken and collapse plastic casing. It is a special concern with thin-wall plastic. The standards list ways to cool a setting seal, such as circulating water inside the casing.

Bulletin 74 sets 20 feet as the minimum seal depth for an individual domestic well. Fresno County requires an annular seal at least 20 feet deep. County staff inspect it, with 48 hours notice. Our guide to well drilling permits covers the county steps. How the hole gets drilled is its own choice, covered in our guide to mud rotary vs air rotary.

Why does sinking ground in the San Joaquin Valley matter for casing?

Parts of the San Joaquin Valley have sunk more than 30 feet as groundwater was pumped, per the U.S. Geological Survey. The USGS notes that well casings sticking up out of the ground are common in farm areas.

Where the ground sinks around a well, stressed casing can fail through collapse and dislocation. Deep wells are the most vulnerable, per the USGS, and the most expensive to repair or replace.

Bulletin 74 names portions of the San Joaquin Valley as places where deep subsidence may occur. There, it calls for keeping the annular seal intact if the ground sinks. One measure it names is a sleeve or slip joint, which lets the casing move up and down without collapsing.

None of this makes one material the answer. It is a reason the casing and the seal get chosen with the ground and the depth in mind.

What does PVC or steel well casing cost?

These are market numbers, not our price list. A home-improvement cost guide lists PVC casing at $6 to $10 per foot. It lists galvanized steel at $36 to $140 per foot, and stainless steel at the same range.

The guide’s depth table puts a 300-foot well at $10,650 with 4-inch PVC casing and $18,360 with 6-inch steel casing. At 400 feet, it shows $14,200 against $24,480. The two columns are different diameters, so the gap is not the material alone.

Casing is one part of the price. The rest depends on the depth, the seal depth the county requires and the ground. The pump and tank, the trench, the electrical run and the permit fee add to it. Our well drilling cost guide covers the market ranges.

Are California’s well casing rules changing?

DWR is updating Bulletin 74. The standards were last updated in 1991, and a public review draft is scheduled for November 2026. Whatever the draft proposes, the county rules in force decide what goes in your well.

How do you choose the casing for your well?

Start with the estimate. Ask which casing material it names, which standard the pipe meets and how deep the casing runs. For plastic, ASTM F480 covers casing made in standard dimension ratios, which compare the pipe’s diameter with its wall thickness.

Big River Drilling is a licensed C-57 well drilling contractor based in Riverdale, working Fresno, Kings and Tulare counties. Our free on-site estimate spells out the depth range, casing, seal, pump and tank for your property. It starts from the well records nearby.

See how our water well drilling works, or call or text (559) 867-3806 for a free on-site estimate.

Frequently asked questions

Is PVC or steel well casing better?
Neither is better for every well. California's well standards allow both. The right casing depends on the depth and diameter, the ground, the water and how the casing goes in.
Is PVC well casing allowed for drinking water wells in California?
Yes, when it meets the standards. Bulletin 74 says plastic well casing must meet ASTM F480. Plastic casing in drinking water wells, household wells included, must also meet NSF Standard 14 and be marked for it.
Can PVC well casing be driven into the ground?
No. Bulletin 74 says plastic casing or screen must not be driven into place or put under excessive stress during installation. Metal casing may be driven, with a drive shoe at the lower end.
Does steel well casing rust?
It depends on the steel. A home-improvement cost guide calls galvanized steel less resistant to corrosion and says stainless steel adds corrosion protection. Bulletin 74 adds that in some cases, the annular seal also protects casing against corrosion.
How deep can PVC well casing go?
Bulletin 74 notes that large diameter plastic casing has not been used extensively below 500 feet. It calls for special care with it in deep wells. The diameter, the ground and the forces on the pipe all shape the choice.
Does the casing size limit the pump?
Yes, the casing has to take the pump. A university extension guide says a 6-inch casing takes pumps that move up to 100 gallons per minute. Above 100, it calls for an 8-inch casing in at least a 10-inch hole.
Is this what Big River Drilling charges?
No, those are market numbers from a home-improvement cost guide, not our price list. The price of your well depends on the depth, the casing, the seal, the ground, the pump and the permit. Our free on-site estimate spells out the depth range, casing, seal, pump and tank for your property. Call or text (559) 867-3806.
Free Estimates

Get In Touch With Big River Drilling

Tell us about the property or what your well is doing, and we will set up a free estimate. For a well or pump problem, call or text (559) 867-3806, day or night.

  • (559) 867-3806
  • Riverdale, CA · serving Fresno, Kings and Tulare counties and out to Kern, Madera and Merced, about 60 to 70 miles around Riverdale
  • Free estimates · new wells, pump repair, pressure tanks and water lines

Get a Free Estimate

Tell us about the well or the water problem. We come out, look at the site and give you a free estimate.

Call (559) 867-3806